Not able to add cisco router Through Switch & router wizards

This support forum board is for support questions relating to Nagios XI, our flagship commercial network monitoring solution.
sarfarosh
Posts: 211
Joined: Fri Oct 05, 2012 3:56 am

Not able to add cisco router Through Switch & router wizards

Post by sarfarosh »

Hello Guys,
I am trying to add Cisco 1721 router to Nagios xi useing Switch & router wizards it don't detect any ports,but if i do use cfgmaker command from command line then it works, attaching the snapshot of wizards error page & output of cfgmaker command, please let me know whatś going wrong over here

Code: Select all

[root@localhost ~]# cfgmaker --show-op-down --zero-speed=100000000 --snmp-options=:::::1 --noreversedns eQuest@192.168.10.201
# Created by 
# /usr/bin/cfgmaker --show-op-down --zero-speed=100000000 --snmp-options=:::::1 --noreversedns eQuest@192.168.10.201


### Global Config Options

#  for UNIX
# WorkDir: /home/http/mrtg

#  or for NT
# WorkDir: c:\mrtgdata

### Global Defaults

#  to get bits instead of bytes and graphs growing to the right
# Options[_]: growright, bits

EnableIPv6: no

######################################################################
# System: equest-mum
# Description: Cisco Internetwork Operating System Software 
#          IOS (tm) C1700 Software (C1700-Y-M), Version 12.3(23), RELEASE SOFTWARE (fc5)
#          Technical Support: http://www.cisco.com/techsupport
#          Copyright (c) 1986-2007 by cisco Systems, Inc.
#          Compiled Tue 24-Jul-07 14:47
# Contact: 
# Location: 
######################################################################


### Interface 1 >> Descr: 'Ethernet0' | Name: 'Et0' | Ip: '192.168.10.201' | Eth: '30-78-30-30-30-64-32-38-64-63-38-66-38-31' ###

Target[192.168.10.201_1]: 1:eQuest@192.168.10.201:::::1
SetEnv[192.168.10.201_1]: MRTG_INT_IP="192.168.10.201" MRTG_INT_DESCR="Ethernet0"
MaxBytes[192.168.10.201_1]: 1250000
Title[192.168.10.201_1]: Traffic Analysis for 1 -- equest-mum
PageTop[192.168.10.201_1]: <h1>Traffic Analysis for 1 -- equest-mum</h1>
		<div id="sysdetails">
			<table>
				<tr>
					<td>System:</td>
					<td>equest-mum in </td>
				</tr>
				<tr>
					<td>Maintainer:</td>
					<td></td>
				</tr>
				<tr>
					<td>Description:</td>
					<td>Ethernet0  </td>
				</tr>
				<tr>
					<td>ifType:</td>
					<td>ethernetCsmacd (6)</td>
				</tr>
				<tr>
					<td>ifName:</td>
					<td>Et0</td>
				</tr>
				<tr>
					<td>Max Speed:</td>
					<td>1250.0 kBytes/s</td>
				</tr>
				<tr>
					<td>Ip:</td>
					<td>192.168.10.201 ()</td>
				</tr>
			</table>
		</div>


### Interface 2 >> Descr: 'FastEthernet0' | Name: 'Fa0' | Ip: '49.248.31.221' | Eth: '30-78-30-30-31-31-35-63-65-31-30-37-64-35' ###

Target[192.168.10.201_2]: 2:eQuest@192.168.10.201:::::1
SetEnv[192.168.10.201_2]: MRTG_INT_IP="49.248.31.221" MRTG_INT_DESCR="FastEthernet0"
MaxBytes[192.168.10.201_2]: 12500000
Title[192.168.10.201_2]: Traffic Analysis for 2 -- equest-mum
PageTop[192.168.10.201_2]: <h1>Traffic Analysis for 2 -- equest-mum</h1>
		<div id="sysdetails">
			<table>
				<tr>
					<td>System:</td>
					<td>equest-mum in </td>
				</tr>
				<tr>
					<td>Maintainer:</td>
					<td></td>
				</tr>
				<tr>
					<td>Description:</td>
					<td>FastEthernet0  </td>
				</tr>
				<tr>
					<td>ifType:</td>
					<td>ethernetCsmacd (6)</td>
				</tr>
				<tr>
					<td>ifName:</td>
					<td>Fa0</td>
				</tr>
				<tr>
					<td>Max Speed:</td>
					<td>12.5 MBytes/s</td>
				</tr>
				<tr>
					<td>Ip:</td>
					<td>49.248.31.221 ()</td>
				</tr>
			</table>
		</div>


### Interface 3 >> Descr: 'Serial0' | Name: 'Se0' | Ip: '' | Eth: '' ###
### The following interface is commented out because:
### * it is administratively DOWN
# 
# Target[192.168.10.201_3]: 3:eQuest@192.168.10.201:::::1
# SetEnv[192.168.10.201_3]: MRTG_INT_IP="" MRTG_INT_DESCR="Serial0"
# MaxBytes[192.168.10.201_3]: 193000
# Title[192.168.10.201_3]: Traffic Analysis for 3 -- equest-mum
# PageTop[192.168.10.201_3]: <h1>Traffic Analysis for 3 -- equest-mum</h1>
# 		<div id="sysdetails">
# 			<table>
# 				<tr>
# 					<td>System:</td>
# 					<td>equest-mum in </td>
# 				</tr>
# 				<tr>
# 					<td>Maintainer:</td>
# 					<td></td>
# 				</tr>
# 				<tr>
# 					<td>Description:</td>
# 					<td>Serial0  </td>
# 				</tr>
# 				<tr>
# 					<td>ifType:</td>
# 					<td>propPointToPointSerial (22)</td>
# 				</tr>
# 				<tr>
# 					<td>ifName:</td>
# 					<td>Se0</td>
# 				</tr>
# 				<tr>
# 					<td>Max Speed:</td>
# 					<td>193.0 kBytes/s</td>
# 				</tr>
# 			</table>
# 		</div>


### Interface 4 >> Descr: 'Null0' | Name: 'Nu0' | Ip: '' | Eth: '' ###
### The following interface is commented out because:
### * it is a cisco Null0 interface
# 
# Target[192.168.10.201_4]: 4:eQuest@192.168.10.201:::::1
# SetEnv[192.168.10.201_4]: MRTG_INT_IP="" MRTG_INT_DESCR="Null0"
# MaxBytes[192.168.10.201_4]: 536870911
# Title[192.168.10.201_4]: Traffic Analysis for 4 -- equest-mum
# PageTop[192.168.10.201_4]: <h1>Traffic Analysis for 4 -- equest-mum</h1>
# 		<div id="sysdetails">
# 			<table>
# 				<tr>
# 					<td>System:</td>
# 					<td>equest-mum in </td>
# 				</tr>
# 				<tr>
# 					<td>Maintainer:</td>
# 					<td></td>
# 				</tr>
# 				<tr>
# 					<td>Description:</td>
# 					<td>Null0  </td>
# 				</tr>
# 				<tr>
# 					<td>ifType:</td>
# 					<td>Other (1)</td>
# 				</tr>
# 				<tr>
# 					<td>ifName:</td>
# 					<td>Nu0</td>
# 				</tr>
# 				<tr>
# 					<td>Max Speed:</td>
# 					<td>536.9 MBytes/s</td>
# 				</tr>
# 			</table>
# 		</div>
You do not have the required permissions to view the files attached to this post.
Top
slansing
Posts: 7698
Joined: Mon Apr 23, 2012 4:28 pm
Location: Travelling through time and space...

Re: Not able to add cisco router Through Switch & router wiz

Post by slansing »

Are you sure that you are using SNMP V2 and not V1? I would run a check on this as it will cause issues.
Top
sarfarosh
Posts: 211
Joined: Fri Oct 05, 2012 3:56 am

Re: Not able to add cisco router Through Switch & router wiz

Post by sarfarosh »

slansing wrote:Are you sure that you are using SNMP V2 and not V1? I would run a check on this as it will cause issues.
slansing have tried both SNMP v1 as well as SNMP v2 but it is not working through Switch& router wizards bt on command line cfgmaker common gives the output......
Top
yancy
Posts: 523
Joined: Thu Oct 06, 2011 10:12 am

Re: Not able to add cisco router Through Switch & router wiz

Post by yancy »

sarfarosh,

Can you post the file permissions of cfgmaker:

Code: Select all

 ll /usr/bin/cfgmaker

Regards,

-Yancy
Top
sarfarosh
Posts: 211
Joined: Fri Oct 05, 2012 3:56 am

Re: Not able to add cisco router Through Switch & router wiz

Post by sarfarosh »

Yancy

Permission of cfgmaker looks good to me below is the output,

Code: Select all

[root@localhost autodiscovery]# ll /usr/bin/cfgmaker 
-rwxr-xr-x. 1 root root 107065 Nov 12  2010 /usr/bin/cfgmaker
Today i also tried Autodiscovery wizards even after been the setup.sh permission been correct

Code: Select all

[root@localhost autodiscovery]# ll
total 64
-rwxr-xr-x. 1 apache nagios 11972 Jan 23 20:33 autodiscovery.inc.php
-rwxr-xr-x. 1 apache nagios   622 Jan 23 20:33 CHANGES.TXT
drwxr-xr-x. 2 apache nagios  4096 Jan 23 20:13 images
-rwxr-xr-x. 1 apache nagios 27369 Jan 23 20:33 index.php
-rwxr-xr-x. 1 apache nagios   521 Jan 23 20:33 install.sh
drwxrwsr-x. 2 apache nagios  4096 Jan 23 20:13 jobs
drwxr-xr-x. 2 apache nagios  4096 Jan 23 20:13 scripts
-rw-r--r--  1 root   root       0 Jan 25 16:02 setup.done
-rwxr-xr-x. 1 apache nagios   353 Jan 23 20:33 setup.sh
Autodiscovery was not able to run setup.sh & gave error to chk permission, it so i had to manually run the script after that autodiscovery runned fine.

but still am not able to make switch/router wizards to detect port of Router, while on command line itś working fine.
Top
scottwilkerson
DevOps Engineer
Posts: 19396
Joined: Tue Nov 15, 2011 3:11 pm
Location: Nagios Enterprises

Re: Not able to add cisco router Through Switch & router wiz

Post by scottwilkerson »

Can we run the following to make sure we don't have an old scan that is sticking around

Code: Select all

rm /usr/local/nagiosxi/tmp/mrtgscan* -f

http://assets.nagios.com/downloads/nagi ... Router.pdf
Former Nagios employee
Creator:
Human Design Website
Get Your Human Design Chart
Top

Return to “Nagios XI”